fan/orangepi-5-plus-kernel
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
Files
1b9711d5e4de5b81494b00a4ae67bf8740c4436b
orangepi-5-plus-kernel/external/config/fex/orangepiplus.fex

1271 lines
46 KiB
Plaintext
Raw Normal View History

first commit
2026-02-07 20:22:48 +08:00
;H3 dolphin-p1 board application
;H3 dolphin-p1 board application
;---------------------------------------------------------------------------------------------------------
; 说明： 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串
; 描述gpio的形式：Port:端口+组内序号<功能分配><内部电阻状态><驱动能力><输出电平状态>
;---------------------------------------------------------------------------------------------------------
[product]
version = "100"
machine = "Xunlong Orange Pi Plus / Plus 2"
;---------------------------------------------------------------------------------------------------------
; eraseflag - 1 erase data partition, 0 - do not erase data partition
; next_work - action after burn, 0x0 by config, 0x1, normal, 0x2 reboot 0x3 ,shutdown,0x4 reupdate ,0x5 boot
;---------------------------------------------------------------------------------------------------------
[platform]
debug_mode = 1
eraseflag = 1
next_work = 2
;----------------------------------------------------------------------------------
;[target] system bootup configuration
;boot_clock = CPU boot frequency, Unit: MHz
;storage_type = boot medium, 0-nand, 1-card0, 2-card2, -1(defualt)auto scan
;----------------------------------------------------------------------------------
[target]
boot_clock = 1008
storage_type = -1
;---------------------------------------------------------------------------------
; uboot key detect enable
; 当keyen_flag = 1 时，支持按键检测
; 当keyen_flag = 0 时，不支持
;---------------------------------------------------------------------------------
[key_detect_en]
keyen_flag = 0
;---------------------------------------------------------------------------------
;"一键进烧写功能"的按键值配置，按住位于min~max范围内的按键都可以强制进烧写
; fel_key_max用于配置按键的最大键值
; fel_key_min用于配置按键的最小键值
;---------------------------------------------------------------------------------
[fel_key]
fel_key_max =07
fel_key_min =02
;----------------------------------------------------------------------------------
;card boot
;logical_start用于配置启动卡上mbr的位置相对于SD卡sector 0的偏移，单位为sector(512byte)
;sprite_gpio0用于配置卡量产时指示灯所用的gpio
;----------------------------------------------------------------------------------
;-------------------------------------------------------------------------------
; sprite_work_delay :
; sprite_err_delay :
; sprite_gpio0 ： 卡量产、一键recovery状态指示灯
; next_work ： 卡量产完成，工作状态(默认关机)
;-------------------------------------------------------------------------------
[card_boot]
logical_start = 40960
sprite_work_delay = 500
sprite_err_delay = 200
sprite_gpio0 = port:PL10<1><default><default><default>
next_work = 3
;---------------------------------------------------------------------------------
; used : 1: used this config, 0: not
; start_type : 1: start system directly when power supply, 0: wait IR/KEY to power on
; irkey_used : 1: ir key used, 0: not
; pmukey_used: 1: physical button used, 0: not
; led_power : 1: light, 0: off
; led_state : 1: light, 0: off
;---------------------------------------------------------------------------------
[box_start_os]
used = 1
start_type = 1
irkey_used = 1
pmukey_used = 1
pmukey_num = 3
led_power = 0
led_state = 0
;-------------------------------------------------------------------------------
; boot阶段上电初始化GPIO
; used :模块使能端 置1：开启模块 置0：关闭模块
; gpiox ：上电初始化gpio （名称自定，但不能重复，并且GPIO允许可以多个）
; PH06 : 系统显示LED GPIO
;-------------------------------------------------------------------------------
[boot_init_gpio]
used = 1
gpio0 = port:PL10<1><default><default><0>
gpio1 = port:PA15<1><default><default><1>
gpio2 = port:PG11<1><default><default><1>
;----------------------------------------------------------------------------------
; used: 模块使能端 1：开启模块 0：关闭模块
; mode: 模式选择 1：一键进入OTA升级 2：一键恢复（通过sysrecovery分区来恢复） 其他值：无效
; recovery_key ： 按键配置 （例如：recovery_key= port:PH16<0><default>）
;----------------------------------------------------------------------------------
[recovery_para]
used = 1
mode = 2
recovery_key = port:PL04<0><default><default><default>
;---------------------------------------------------------------------------------------------------------
; if 1 == standby_mode, then support super standby;
; else, support normal standby.
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 1
[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 8
sdc_cmd = port:PC06<3><1><2><default>
sdc_clk = port:PC05<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
sdc_2xmode = 1
sdc_ddrmode = 1
[twi_para]
twi_port = 0
twi_scl = port:PA11<2><default><default><default>
twi_sda = port:PA12<2><default><default><default>
[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PA04<2><1><default><default>
uart_debug_rx = port:PA05<2><1><default><default>
[force_uart_para]
force_uart_port = 0
force_uart_tx = port:PF02<3><1><default><default>
force_uart_rx = port:PF04<3><1><default><default>
[jtag_para]
jtag_enable = 0
jtag_ms = port:PA00<3><default><default><default>
jtag_ck = port:PA01<3><default><default><default>
jtag_do = port:PA02<3><default><default><default>
jtag_di = port:PA03<3><default><default><default>
[clock]
pll_video = 297
pll_ve = 402
pll_periph0 = 600
pll_gpu = 576
pll_periph1 = 600
pll_de = 864
;*****************************************************************************
;sdram configuration
;
;dram_para2 = 0x00001200 ;Representative enable dram Dual
;
;dram_para2 = 0x00001100 ;on behalf of a single channel is enabled dram
;
;*****************************************************************************
[dram_para]
dram_clk = 624
dram_type = 3
dram_zq = 0x3b3bfb
dram_odt_en = 0x1
dram_para1 = 0x10E40000
dram_para2 = 0x0000
dram_mr0 = 0x1840
dram_mr1 = 0x40
dram_mr2 = 0x18
dram_mr3 = 0x2
dram_tpr0 = 0x0048A192
dram_tpr1 = 0x01C2418D
dram_tpr2 = 0x00076051
dram_tpr3 = 0
dram_tpr4 = 0
dram_tpr5 = 0
dram_tpr6 = 100
dram_tpr7 = 0
dram_tpr8 = 0
dram_tpr9 = 0
dram_tpr10 = 0
dram_tpr11 = 0x6aaa0000
dram_tpr12 = 0x7979
dram_tpr13 = 0x800800
;----------------------------------------------------------------------------------
;os life cycle para configuration
;----------------------------------------------------------------------------------
;---------------------------------------------------------------------------------------------------------
; wakeup_src_para:
; sometimes, u would like to add more wakeup src in standby mode, these para will be
; help;
; u need to make sure the standby mode support the wakeup src. Also, some hw
; condition must be guaranteed.
; including:
; cpu_en: power on or off.
; 1: mean power on
; 0: mean power off
; cpu_freq: indicating lowest freq. unit is Mhz;
; dram selfresh_en: selfresh or not.
; 1: enable enter selfresh
; 0: disable enter selfresh
; dram_pll: if not enter selfresh, indicating lowest freq. unit is Mhz;
; wakeup_src: to make the scenario work, the wakeup src is needed.
;---------------------------------------------------------------------------------------------------------
[wakeup_src_para]
cpu_en = 0
cpu_freq = 48
; (cpu:apb:ahb)
pll_ratio = 0x111
dram_selfresh_en = 1
dram_freq = 36
wakeup_src0 =
wakeup_src_wl = port:PG10<4><default><default><0>
wakeup_src_bt = port:PL03<6><default><default><0>
;----------------------------------------------------------------------------------
;i2c configuration
;----------------------------------------------------------------------------------
[twi0]
twi_used = 1
twi_scl = port:PA11<2><default><default><default>
twi_sda = port:PA12<2><default><default><default>
[twi1]
twi_used = 1
twi_scl = port:PA18<3><default><default><default>
twi_sda = port:PA19<3><default><default><default>
[twi2]
twi_used = 0
twi_scl = port:PE12<3><default><default><default>
twi_sda = port:PE13<3><default><default><default>
;----------------------------------------------------------------------------------
;uart configuration
;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function)
;----------------------------------------------------------------------------------
[uart0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PA04<2><1><default><default>
uart_rx = port:PA05<2><1><default><default>
[uart1]
uart_used = 0
uart_port = 1
uart_type = 2
uart_tx = port:PG06<2><1><default><default>
uart_rx = port:PG07<2><1><default><default>
;uart_rts = port:PG08<2><1><default><default>
;uart_cts = port:PG09<2><1><default><default>
[uart2]
uart_used = 1
uart_port = 2
uart_type = 4
uart_tx = port:PA00<2><1><default><default>
uart_rx = port:PA01<2><1><default><default>
uart_rts = port:PA02<2><1><default><default>
uart_cts = port:PA03<2><1><default><default>
[uart3]
uart_used = 1
uart_port = 3
uart_type = 2
uart_tx = port:PA13<3><1><default><default>
uart_rx = port:PA14<3><1><default><default>
uart_rts = port:PA15<3><1><default><default>
uart_cts = port:PA16<3><1><default><default>
;----------------------------------------------------------------------------------
;SPI controller configuration
;----------------------------------------------------------------------------------
[spi0]
spi_used = 1
spi_cs_bitmap = 1
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_cs0 = port:PC03<3><1><default><default>
[spi1]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA13<2><1><default><default>
spi_sclk = port:PA14<2><default><default><default>
spi_mosi = port:PA15<2><default><default><default>
spi_miso = port:PA16<2><default><default><default>
;----------------------------------------------------------------------------------
;SPI device configuration
;----------------------------------------------------------------------------------
[spi_devices]
spi_dev_num = 1
[spi_board0]
modalias = "spidev"
max_speed_hz = 33000000
bus_num = 0
chip_select = 0
mode = 0
full_duplex = 1
manual_cs = 0
; NOTE: This section is necessary only for "gpio_sunxi" driver
; which is obsolete for H3 boards
[gpio_para]
gpio_used = 0
gpio_num = 0
;[led_assign]
;normal_led = "gpio_pin_2"
;standby_led = "gpio_pin_1"
[leds_para]
leds_used = 1
green_led = port:PL10<1><default><default><1>
green_led_active_low = 0
red_led = port:PA15<1><default><default><0>
red_led_active_low = 0
;----------------------------------------------------------------------------------
;thermal configuration
;ths_trip_count : temperature trigger number
;ths_trip_0 : first temperature trigger
;ths_trip_1 : second temperature trigger
;ths_trip_2 : third temperature trigger, when upto this temperature, system shutdown
;ths_trip_0_min : first temperature trigger's min freq
;ths_trip_0_max : first temperature trigger's max freq
;ths_trip_1_min : second temperature trigger's min freq
;ths_trip_1_max : second temperature trigger's max freq
;----------------------------------------------------------------------------------
[ths_para]
ths_used = 1
ths_trip1_count = 6
ths_trip1_0 = 75
ths_trip1_1 = 80
ths_trip1_2 = 85
ths_trip1_3 = 90
ths_trip1_4 = 95
ths_trip1_5 = 105
ths_trip1_6 = 0
ths_trip1_7 = 0
ths_trip1_0_min = 0
ths_trip1_0_max = 1
ths_trip1_1_min = 1
ths_trip1_1_max = 2
ths_trip1_2_min = 2
ths_trip1_2_max = 3
ths_trip1_3_min = 3
ths_trip1_3_max = 4
ths_trip1_4_min = 4
ths_trip1_4_max = 8
ths_trip1_5_min = 8
ths_trip1_5_max = 8
ths_trip1_6_min = 0
ths_trip1_6_max = 0
ths_trip2_count = 1
ths_trip2_0 = 105
;----------------------------------------------------------------------------------
;cooler_table cooler_count <=32
;----------------------------------------------------------------------------------
[cooler_table]
cooler_count = 9
cooler0 = "1296000 4 4294967295 0"
cooler1 = "1200000 4 4294967295 0"
cooler2 = "1008000 4 4294967295 0"
cooler3 = "816000 4 4294967295 0"
cooler4 = "648000 4 4294967295 0"
cooler5 = "480000 4 4294967295 0"
cooler6 = "480000 3 4294967295 0"
cooler7 = "480000 2 4294967295 0"
cooler8 = "480000 1 4294967295 0"
[nand0_para]
nand_support_2ch = 0
nand0_used = 0
nand0_we = port:PC00<2><default><default><default>
nand0_ale = port:PC01<2><default><default><default>
nand0_cle = port:PC02<2><default><default><default>
nand0_ce1 = port:PC03<2><default><default><default>
nand0_ce0 = port:PC04<2><default><default><default>
nand0_nre = port:PC05<2><default><default><default>
nand0_rb0 = port:PC06<2><default><default><default>
nand0_rb1 = port:PC07<2><default><default><default>
nand0_d0 = port:PC08<2><default><default><default>
nand0_d1 = port:PC09<2><default><default><default>
nand0_d2 = port:PC10<2><default><default><default>
nand0_d3 = port:PC11<2><default><default><default>
nand0_d4 = port:PC12<2><default><default><default>
nand0_d5 = port:PC13<2><default><default><default>
nand0_d6 = port:PC14<2><default><default><default>
nand0_d7 = port:PC15<2><default><default><default>
nand0_ndqs = port:PC16<2><default><default><default>
;-----------------------------------------------------------------
;auto_hpd - 1:need hotplud for hdmi/tv; 0:don't hotplud for lcd
;output_type - 0:none; 1:lcd; 2:tv; 4:hdmi; 8:vga (as default config in homlet)
;hdmi_channel- the display channel for hdmi (as default config in homlet)
;cvbs_channel- the display channel for cvbs (as default config in homlet)
;hdmi_mode - as default config for output of hdmi in homlet
;cvbs_mode - as default config for output of tv in homlet. 11:PAL; 14:NTSC
;check the definition(of hdmi/cvbs_mode) of disp_tv_mode in sunxi_display2.h
;hdmi_mode_check - disable/enable the function of checking hdmi mode, 0 is disable, 1 is enable
;-----------------------------------------------------------------
[boot_disp]
advert_disp = 0
auto_hpd = 1
output_type = 4
hdmi_channel = 0
hdmi_mode = 4
cvbs_channel = 1
cvbs_mode = 11
output_full = 1
hdmi_mode_check = 1
;----------------------------------------------------------------------------------
;disp init configuration
;
;disp_mode (0:screen0<screen0,fb0>; 1:screen1<screen1,fb0>)
;screenx_output_type (0:none; 1:lcd; 3:hdmi;)
;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50)
; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60)
;fbx format (0:ARGB 1:ABGR 2:RGBA 3:BGRA 5:RGB565 8:RGB888 12:ARGB4444 16:ARGB1555 18:RGBA5551)
;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0)
;lcdx_backlight (lcd init backlight,the range:[0,256],default:197
;----------------------------------------------------------------------------------
[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 3
screen0_output_mode = 5
screen1_output_type = 3
screen1_output_mode = 5
fb0_format = 0
fb0_width = 0
fb0_height = 0
fb1_format = 0
fb1_width = 0
fb1_height = 0
fb0_framebuffer_num = 3
sunxi_fb_mem_reserve = 32
;----------------------------------------------------------------------------------
;hdmi configuration
;----------------------------------------------------------------------------------
[hdmi_para]
hdmi_used = 1
hdmi_power = "vcc-hdmi-18"
;-------------------------------------
; set to 0 for hdmi->dvi compatibility
;-------------------------------------
;hdcp_enable = 0
;hdmi_cts_compatibility = 1
[tv_para]
tv_used = 0
tv_dac_used = 1
tv_dac_src0 = 0
;----------------------------------------------------------------------------------
;pwm config
;----------------------------------------------------------------------------------
[pwm0_para]
pwm_used = 0
pwm_positive = port:PA05<3><0><default><default>
;------------------------------------------------------------------------------;
; 10/100/100Mbps Ethernet MAC Controller Configure ;
;------------------------------------------------------------------------------;
; Options: ;
; gmac_used --- 0: not used, 1: external phy, 2: internal phy ;
; gmac_powerx -- A[:B] A: axp channel, B: voltage value ;
; If set gamc_phy to use internal PHY, do not config port ;
;------------------------------------------------------------------------------;
; MII RMII MII RMII MII RMII ;
; PD00 * PD06 * * PD12 * * ;
; PD01 * PD07 * PD13 * * ;
; PD02 * * PD08 * PD14 * ;
; PD03 * * PD09 * * PD15 * ;
; PD04 * PD10 * * PD16 * * ;
; PD05 * PD11 * * PD17 * * ;
;------------------------------------------------------------------------------;
[gmac0]
gmac_used = 1
gmac_rxd3 = port:PD00<2><default><3><default>
gmac_rxd2 = port:PD01<2><default><3><default>
gmac_rxd1 = port:PD02<2><default><3><default>
gmac_rxd0 = port:PD03<2><default><3><default>
gmac_rxclk = port:PD04<2><default><3><default>
gmac_rxdv = port:PD05<2><default><3><default>
;gmac_rxerr = port:PD06<2><default><3><default>
gmac_txd3 = port:PD07<2><default><3><default>
gmac_txd2 = port:PD08<2><default><3><default>
gmac_txd1 = port:PD09<2><default><3><default>
gmac_txd0 = port:PD10<2><default><3><default>
;gmac_crs = port:PD11<2><default><3><default>
gmac_txclk = port:PD12<2><default><3><default>
gmac_txen = port:PD13<2><default><3><default>
;gmac_txerr = port:PD14<2><default><3><default>
gmac_col = port:PD15<2><default><3><default>
gmac_mdc = port:PD16<2><default><3><default>
gmac_mdio = port:PD17<2><default><3><default>
gmac_power1 =
[gmac_phy_power]
gmac_phy_power_en = port:PD06<1><default><default><0>
;--------------------------------------------------------------------------------
;vip (video input port) configuration
;vip_used: 0:disable 1:enable
;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer
;vip_dev_qty: The quantity of devices linked to capture bus
;
;vip_define_sensor_list: If you want use sensor detect function, please set vip_define_sensor_list = 1, and
; verify that file /system/etc/hawkview/sensor_list_cfg.ini is properly configured!
;
;vip_dev(x)_pos: sensor position, "rear" or "front", if vip_define_sensor_list = 1,
;vip_dev(x)_pos must be configured!
;
;vip_dev(x)_isp_used 0:not use isp 1:use isp
;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb
;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby
;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable
;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable
;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply
;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply
;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply
;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply
;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply
;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply
;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply
;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply
;x indicates the index of the devices which are linked to the same capture bus
;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000
;fill handle string as below:
;axp22_eldo3
;axp22_dldo4
;axp22_eldo2
;fill handle string "" when not using any pmu power supply
;--------------------------------------------------------------------------------
[csi0]
vip_used = 1
vip_mode = 0
vip_dev_qty = 1
vip_define_sensor_list = 0
vip_csi_pck = port:PE00<2><default><default><default>
vip_csi_mck = port:PE01<2><default><default><default>
vip_csi_hsync = port:PE02<2><default><default><default>
vip_csi_vsync = port:PE03<2><default><default><default>
vip_csi_d0 = port:PE04<2><default><default><default>
vip_csi_d1 = port:PE05<2><default><default><default>
vip_csi_d2 = port:PE06<2><default><default><default>
vip_csi_d3 = port:PE07<2><default><default><default>
vip_csi_d4 = port:PE08<2><default><default><default>
vip_csi_d5 = port:PE09<2><default><default><default>
vip_csi_d6 = port:PE10<2><default><default><default>
vip_csi_d7 = port:PE11<2><default><default><default>
vip_csi_sck = port:PE12<2><default><default><default>
vip_csi_sda = port:PE13<2><default><default><default>
vip_dev0_mname = "gc2035"
vip_dev0_pos = "front"
vip_dev0_lane = 1
vip_dev0_twi_id = 2
vip_dev0_twi_addr = 0x78
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 1
vip_dev0_hflip = 1
vip_dev0_iovdd = ""
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = ""
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = ""
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = ""
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en = port:PA17<1><default><default><1>
vip_dev0_reset = port:PE14<1><default><default><1>
vip_dev0_pwdn = port:PE15<1><default><default><0>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =
vip_dev0_act_used = 0
vip_dev0_act_name = "ad5820_act"
vip_dev0_act_slave = 0x18
vip_dev1_mname = ""
vip_dev1_pos = "rear"
vip_dev1_lane = 1
vip_dev1_twi_id = 0
vip_dev1_twi_addr =
vip_dev1_isp_used = 0
vip_dev1_fmt = 1
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_iovdd = ""
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = ""
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = ""
vip_dev1_dvdd_vol = 1500000
vip_dev1_afvdd = ""
vip_dev1_afvdd_vol = 2800000
vip_dev1_power_en =
vip_dev1_reset =
vip_dev1_pwdn =
vip_dev1_flash_en =
vip_dev1_flash_mode =
vip_dev1_af_pwdn =
;--------------------------------------------------------------------------------
;tv configuration
;
;--------------------------------------------------------------------------------
[tvout_para]
tvout_used = 0
tvout_channel_num =
tv_en = 0
[tvin_para]
tvin_used = 0
tvin_channel_num =
;----------------------------------------------------------------------------------
;DE-Interlace configuration
;----------------------------------------------------------------------------------
[di_para]
di_used = 1
;--------------------------------------------------------------------------------
; SDMMC PINS MAPPING |
; ------------------------------------------------------------------------------|
; Config Guide |
; sdc_used: 1-enable card, 0-disable card |
; sdc_detmode: card detect mode |
; 1-detect card by gpio polling |
; 2-detect card by gpio irq(must use IO with irq function) |
; 3-no detect, always in for boot card |
; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert|
; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit |
; sdc_use_wp: 1-with write protect IO, 0-no write protect IO |
; sdc_isio: for sdio card |
; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for|
; SD3.0 or eMMC4.5, regulator must be configured. the value is |
; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2" |
; other: GPIO Mapping configuration |
; ------------------------------------------------------------------------------|
; Note: |
; 1 if detmode=2, sdc_det's config=6 |
; else if detmode=1, sdc_det's config=0 |
; else sdc_det IO is not necessary |
; 2 if the customer wants to support UHS-I and HS200 features, he must provide|
; an independent power supply for the card. This is only used in platforms |
; that supports SD3.0 cards and eMMC4.4+ flashes |
;--------------------------------------------------------------------------------
[mmc0_para]
sdc_used = 1
sdc_detmode = 3
sdc_buswidth = 4
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_d1 = port:PF00<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_det = port:PF06<0><1><2><default>
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
sdc_power_supply = "none"
[mmc1_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><3><default>
sdc_cmd = port:PG01<2><1><3><default>
sdc_d0 = port:PG02<2><1><3><default>
sdc_d1 = port:PG03<2><1><3><default>
sdc_d2 = port:PG04<2><1><3><default>
sdc_d3 = port:PG05<2><1><3><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"
sdc_power_supply = "none"
sdc_2xmode = 1
sdc_ddrmode = 1
[mmc2_para]
sdc_used = 1
sdc_detmode = 3
sdc_buswidth = 8
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
sdc_power_supply = "none"
sdc_2xmode = 1
sdc_ddrmode = 1
; ------------------------------------------------------------------------------|
; sim card configuration
;--------------------------------------------------------------------------------
[smc_para]
smc_used = 0
smc_rst = port:PA09<2><default><default><default>
smc_vppen = port:PA20<3><default><default><default>
smc_vppp = port:PA21<3><default><default><default>
smc_det = port:PA10<2><default><default><default>
smc_vccen = port:PA06<2><default><default><default>
smc_sck = port:PA07<2><default><default><default>
smc_sda = port:PA08<2><default><default><default>
;--------------------------------
; [usbc0]: Controller 0 configuration.
; usb used: USB enable flag. Set, indicating that the system USB module is available, is set to 0, it means that the system USB is disabled.
; usb_port_type: USB port usage. 0: device only; 1: host only; 2: OTG
; usb_detect_type: USB port of checking. 0: not detected; 1: vbus / id checks; 2: id / dpdm check
; usb_id_gpio: USB ID pin pin configuration. For details, please refer gpio configuration instructions.
; usb_det_vbus_gpio: USB DET_VBUS pin pin configuration. For details, please refer gpio configuration instructions.
; usb_drv_vbus_gpio: USB DRY_VBUS pin pin configuration. For details, please refer gpio configuration instructions.
; usb_det_vbus_gpio: "axp_ctrl", represents axp offer
; usb_restrict_gpio: usb limiting control pin
; usb_restric_flag: usb limiting standard set
;--------------------------------
;--------------------------------
;--- USB0控制标志
;--------------------------------
[usbc0]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_id_gpio =
usb_det_vbus_gpio =
usb_drv_vbus_gpio = port:PL02<1><0><default><0>
usb_host_init_state = 1
usb_restrict_gpio =
usb_restric_flag = 0
usb_restric_voltage = 3550000
usb_restric_capacity= 5
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0
;--------------------------------
;--- USB1控制标志
;--------------------------------
[usbc1]
usb_used = 1
usb_drv_vbus_gpio = port:PG13<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0
;--------------------------------
;--- USB2控制标志
;--------------------------------
[usbc2]
usb_used = 0
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0
;--------------------------------
;--- USB3控制标志
;--------------------------------
[usbc3]
usb_used = 1
;usb_drv_vbus_gpio = port:PG11<1><default><default><1>
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0
;--------------------------------
;--- USB Device
;--------------------------------
[usb_feature]
vendor_id = 0x18D1
mass_storage_id = 0x0001
adb_id = 0x0002
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"
[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 3
[serial_feature]
serial_unique = 0
;--------------------------------------------------------------------------------
;wifi/bt/fm/gps/nfc modules configuration
;module_num:
; 0- none
; 1- rtl8188eu(wifi)
; 2- rtl8723bs(wifi+bt)
; 3- ap6181(wifi)
; 4- ap6210(wifi+bt)
; 5- ap6330(wifi+bt)
; 6- ap6335(wifi)
; 7- rtl8189etv(wifi)
;module_power0: axp used by module, "axp22_dldo1" - use dldo1, not use keep it empty
;module_power0_vol: power0 voltage, mv;
;chip_en: enable chip io
;lpo_use_apclk: ""- not use, "losc_out"- a23/33/H3, "ac10032k1"、"ac10032k2"、"ac10032k3"- a80
;--------------------------------------------------------------------------------
[module_para]
module_num = 7
module_power0 = "vcc-wifi-33"
module_power0_vol = 0
module_power1 =
module_power1_vol =
module_power2 =
module_power2_vol =
module_power3 =
module_power3_vol =
chip_en =
lpo_use_apclk =
;--------------------------------------------------------------------------------
;wifi configuration
;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2
;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0)
;wl_reg_on: wifi function enable pin
;wl_host_wake: wlan device wake-up host pin
;wl_host_wake_invert: whether wl_host_wake use inverter between ap and module
; 0: not used, 1: used
;--------------------------------------------------------------------------------
[wifi_para]
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 2
wifi_usbc_type = 1
wl_reg_on = port:PL07<1><default><default><0>
wl_host_wake = port:PG10<0><default><default><0>
wl_host_wake_invert = 0
;--------------------------------------------------------------------------------
;bluetooth configuration
;bt_used: 0- no used, 1- used
;bt_uard_id: 0- uart0, 1- uart1, 2- uart2
;bt_rst_n: bt function enable io
;bt_wake: host wake-up bluetooth device
;bt_host_wake: bt device wake-up host
;bt_host_wake_invert: whether bt_host_wake use inverter between ap and module
; 0: not used, 1: used
;--------------------------------------------------------------------------------
[bt_para]
bt_used = 0
bt_uart_id = 1
bt_rst_n =
bt_wake =
bt_host_wake =
bt_host_wake_invert = 0
;--------------------------------------------------------------------------------
;daudio_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;daudio_select:0 is pcm.1 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[pcm0]
daudio_used = 0
daudio_master = 4
daudio_select = 1
audio_format = 1
signal_inversion = 1
mclk_fs = 128
sample_resolution = 16
slot_width_select = 32
;pcm_sync_period = 256
pcm_lrck_period = 32
pcm_lrckr_period = 1
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 32
frame_width = 0
tx_data_mode = 0
rx_data_mode = 0
i2s_mclk = port:PA18<2><1><default><default>
i2s_bclk = port:PA19<2><1><default><default>
i2s_dout0 = port:PA20<2><1><default><default>
i2s_din = port:PA21<2><1><default><default>
[pcm1]
daudio_used = 0
daudio_master = 4
daudio_select = 1
audio_format = 1
signal_inversion = 1
mclk_fs = 128
sample_resolution = 16
slot_width_select = 32
;pcm_sync_period = 256
pcm_lrck_period = 32
pcm_lrckr_period = 1
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 32
frame_width = 0
tx_data_mode = 0
rx_data_mode = 0
i2s_mclk = port:PG10<2><1><default><default>
i2s_bclk = port:PG11<2><1><default><default>
i2s_dout0 = port:PG12<2><1><default><default>
i2s_din = port:PG13<2><1><default><default>
[audio0]
audio_used = 1
lineout_vol = 0x1f
cap_vol = 0x5
audio_hp_ldo = "none"
adcagc_used = 0
adcdrc_used = 0
dacdrc_used = 0
adchpf_used = 0
dachpf_used = 0
audio_pa_ctrl = port:PA16<1><default><default><0>
[spdif0]
spdif_used = 0
spdif_dout = port:PA17<2><1><default><default>
[audiohub]
hub_used = 0
codec_used = 1
spdif_used = 1
hdmi_used = 1
;----------------------------------------------------------------------------------
;ir rx --- infra remote configuration
;----------------------------------------------------------------------------------
[s_cir0]
ir_used = 1
ir_rx = port:PL11<2><1><default><default>
ir_power_key_code0 = 0x57
ir_addr_code0 = 0x9f00
ir_power_key_code1 = 0x1a
ir_addr_code1 = 0xfb04
ir_power_key_code2 = 0x14
ir_addr_code2 = 0x7F80
ir_power_key_code3 = 0x15
ir_addr_code3 = 0x7F80
ir_power_key_code4 = 0x0b
ir_addr_code4 = 0xF708
ir_power_key_code5 = 0x03
ir_addr_code5 = 0x00EF
ir_power_key_code6 = 0x9f
ir_addr_code6 = 0x4CB3
ir_power_key_code7 = 0x0a
ir_addr_code7 = 0x7748
ir_power_key_code8 = 0x45
ir_addr_code8 = 0xbd02
ir_power_key_code9 = 0x4d
ir_addr_code9 = 0xde21
ir_power_key_code10 = 0x18
ir_addr_code10 = 0xfe01
ir_power_key_code11 = 0x57
ir_addr_code11 = 0xff00
ir_power_key_code12 = 0x4d
ir_addr_code12 = 0xff40
;----------------------------------------------------------------------------------
;ir tx--- infra remote configuration
;----------------------------------------------------------------------------------
[cir]
ir_used = 1
ir_tx = port:PH07<2><default><default><default>
;----------------------------------------------------------------------------------
; dvfs voltage-frequency table configuration
;
; pmuic_type:0:none, 1:gpio, 2:i2c
; pmu_gpio0: gpio config.
; pmu_levelx: 0~9999: voltage(mV), 10000~90000:gpio0 state. voltage form high to low.
;
; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk
; 1536MHz@1500mV with radiator, 1296MHz@1340mV without radiator
; max_freq: cpu maximum frequency, based on Hz, can not be more than 1200MHz
; min_freq: cpu minimum frequency, based on Hz, can not be less than 60MHz
;
; LV_count: count of LV_freq/LV_volt, must be < 16
;
; LV1: core vdd is 1.50v if cpu frequency is (1296Mhz, 1536Mhz]
; LV2: core vdd is 1.34v if cpu frequency is (1200Mhz, 1296Mhz]
; LV3: core vdd is 1.32v if cpu frequency is (1008Mhz, 1200Mhz]
; LV4: core vdd is 1.20v if cpu frequency is (816Mhz, 1008Mhz]
; LV5: core vdd is 1.10v if cpu frequency is (648Mhz, 816Mhz]
; LV6: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
; LV7: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
; LV8: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
;
;----------------------------------------------------------------------------------
[dvfs_table]
pmuic_type = 2
pmu_gpio0 = port:PL06<1><1><2><1>
pmu_level0 = 11300
pmu_level1 = 1100
extremity_freq = 1296000000
max_freq = 1200000000
min_freq = 480000000
LV_count = 7
LV1_freq = 1296000000
LV1_volt = 1320
LV2_freq = 1200000000
LV2_volt = 1240
LV3_freq = 1104000000
LV3_volt = 1180
LV4_freq = 1008000000
LV4_volt = 1140
LV5_freq = 960000000
LV5_volt = 1080
LV6_freq = 816000000
LV6_volt = 1020
LV7_freq = 480000000
LV7_volt = 980
[gpu_dvfs_table]
G_LV_count = 3
G_LV0_freq = 312000000
G_LV0_volt = 1200000
G_LV1_freq = 384000000
G_LV1_volt = 1200000
G_LV2_freq = 456000000
G_LV2_volt = 1200000
;----------------------------------------------------------------------------------
;virtual device
;virtual device for pinctrl testing
;device have pin PA1 PA2
;----------------------------------------------------------------------------------
[Vdevice]
Vdevice_used = 0
Vdevice_0 = port:PH10<5><1><2><default>
Vdevice_1 = port:PH11<5><1><2><default>
;----------------------------------------------------------------------------------
;s_uart0 config parameters
;s_uart_used --s_uart0 whether used for arisc debugging
;----------------------------------------------------------------------------------
[s_uart0]
s_uart_used = 0
s_uart_tx = port:PL02<2><default><default><default>
s_uart_rx = port:PL03<2><default><default><default>
;----------------------------------------------------------------------------------
;s_rsb0 config parameters
;s_rsb_used --s_rsb0 whether used for arisc
;----------------------------------------------------------------------------------
[s_rsb0]
s_rsb_used = 1
s_rsb_sck = port:PL00<2><1><2><default>
s_rsb_sda = port:PL01<2><1><2><default>
;----------------------------------------------------------------------------------
;s_jtag0 config parameters
;s_jtag0_used --s_jtag0 whether used for arisc
;
;----------------------------------------------------------------------------------
[s_jtag0]
s_jtag_used = 0
s_jtag_tms = port:PL04<2><1><2><default>
s_jtag_tck = port:PL05<2><1><2><default>
s_jtag_tdo = port:PL06<2><1><2><default>
s_jtag_tdi = port:PL07<2><1><2><default>
;----------------------------------------------------------------------------------
;s_powchk cpus power check
;s_powchk_used --power check whether used for arisc in super standby
; bit31:enable power updat, bit1:wakeup when power state exception
; bit0:wakeup when power consumption exception
;s_power_reg the expected regs stand for power on/off state
;s_system_power the limit maxmum power consumption when super standby (unit: mw)
;
;----------------------------------------------------------------------------------
[s_powchk]
s_powchk_used = 0x80000000
s_power_reg = 0x00000000
s_system_power = 50
;----------------------------------------------------------------------------------
;scr configuration
;----------------------------------------------------------------------------------
[sim0]
scr_used = 0
scr_vccen = port:PA06<2><default><default><default>
scr_slk = port:PA07<2><default><default><default>
scr_sda = port:PA08<2><default><default><default>
scr_rst = port:PA09<2><default><default><default>
scr_det = port:PA10<2><default><default><default>
;--------------------------------------------------------------------------------
;tsc configuration
;--------------------------------------------------------------------------------
[ts0]
tsc_used = 0
tsc_clk = port:PE00<3><default><default><default>
tsc_err = port:PE01<3><default><default><default>
tsc_sync = port:PE02<3><default><default><default>
tsc_dvld = port:PE03<3><default><default><default>
tsc_d0 = port:PE04<3><default><default><default>
tsc_d1 = port:PE05<3><default><default><default>
tsc_d2 = port:PE06<3><default><default><default>
tsc_d3 = port:PE07<3><default><default><default>
tsc_d4 = port:PE08<3><default><default><default>
tsc_d5 = port:PE09<3><default><default><default>
tsc_d6 = port:PE10<3><default><default><default>
tsc_d7 = port:PE11<3><default><default><default>
;--------------------------------------------------------------------------------
;gpio key
;--------------------------------------------------------------------------------
[gpio_power_key]
key_used = 1
key_io = port:PL03<6><default><default><0>
;----------------------------------------------------------------------------------
; key para
;
; key_used --0:not used, 1:used
; key_cnt --how many key button attach to keyadc.
; key*_vol --the threshold of input voltage of key.
;
; For example: if key2_vol < $(keyadc value) < key3_vol, then key3 be reported.
;----------------------------------------------------------------------------------
[key_para]
key_used = 0
key_cnt = 5
key1_vol = 222
key2_vol = 444
key3_vol = 666
key4_vol = 857
key5_vol = 2000
;----------------------------------------------------------------------------------
;display seven segment para
;----------------------------------------------------------------------------------
[d7s_para]
d7s_used = 0
din_gpio = port:PD00<1><default><default><1>
clk_gpio = port:PD01<1><default><default><1>
stb_gpio = port:PD02<1><default><default><1>
;----------------------------------------------------------------------------------
;mali parameters
;----------------------------------------------------------------------------------
[mali_para]
mali_used = 1
mali_clkdiv = 1
mali_extreme_freq = 600
mali_extreme_vol = 1400
;----------------------------------------------------------------------------------
;1wire parameters (default - PA20)
;----------------------------------------------------------------------------------
[w1_para]
w1_used = 1
gpio = 20
[corekeeper]
corekeeper_enabled = 1
Reference in New Issue Copy Permalink